InkBags repairs the printhead in the Printware iJetColor Pro 1175P. High-speed envelope and direct-mail press built on the HP FI-1000, launched by Printware in 2020. Recovery is realistic when the fault is dried ink, blockage, contamination or air-lock; it is not when a die segment is electrically dead or the nozzle plate is damaged. Send a nozzle test print and we tell you which one you have before quoting.
Printware iJetColor Pro 1175P printhead specification
Parts and recovery procedures do not transfer between printhead families, even when both are HP thermal inkjet — so the engine inside the machine is the first thing to establish.
| Machine | iJetColor Pro 1175P — Printware, USA |
| Print engine | HP FI-1000 Fixed Imager |
| Print width | 297 mm / 11.7 in |
| Resolution | Up to 1200 dpi |
| Ink | HP pigment, CMYK |
| Typical application | Envelopes, direct mail, variable-data mailing work |
What printhead failure looks like on a iJetColor Pro 1175P
- Banding across envelope faces that lands in the same place on every piece in the run.
- Nozzle loss concentrated on the black channel — common on mailing work with heavy address-block and barcode coverage.
- Dropouts appearing after a shift change where the machine was left uncapped between jobs.
- Barcode and address-block quality falling below mail-scanning tolerance while the rest of the piece still looks acceptable.
Photograph the nozzle test print before running any more recovery cycles. Repeated aggressive purging on a head that has already dried out can turn a recoverable fault into a replacement.
How we approach a iJetColor Pro 1175P printhead
On mailing work the commercial stakes of nozzle loss are different: a barcode or address block that drops below scan tolerance fails the whole mailing, even when the graphic areas still look fine. We test specifically for readability, not only for visual banding.
Envelope stock is typically less abrasive than the packaging board a BM300 runs, so on the 1175P the failure driver is more often idle time and drying than mechanical contamination — which changes the recovery procedure.
We check the black channel first on this machine, because that is where mailing workloads concentrate wear.
What the service covers
Diagnosis
Failure-mode identification from the nozzle test print, plus a straight answer on whether recovery is realistic.
Nozzle recovery
Deep flushing of the ink path and restoration of blocked nozzle areas, matched to the failure mode.
Ink system service
Capping, wiping and supply-side inspection — the parts that usually caused the failure in the first place.
Replacement printheads are available where recovery is not viable, along with original and compatible ink, so a machine that cannot be recovered does not sit idle waiting on a separate supplier.
Pricing and turnaround are quoted per case, because both depend on the failure mode and on whether the ink delivery system needs work as well.
Printware iJetColor Pro 1175P printhead repair FAQ
Our 1175P is dropping nozzles on black only. What causes that?
Uneven channel wear. Mailing work puts most of its coverage — addresses, barcodes, text — on black, so that channel accumulates far more firing cycles than cyan, magenta or yellow. It is usually recoverable, but it is also a signal that the maintenance interval needs to change.
Can you repair the head without taking the press out of service for weeks?
Turnaround depends on the failure mode and on parts availability. Send us the nozzle test and we will tell you the realistic timeline before you dismantle anything.
Can the Printware iJetColor Pro 1175P printhead be repaired or does it need replacing?
Both happen. Blockage, dried ink, contamination and air-lock recover in a large share of cases; electrical or physical damage to the die does not. The nozzle test print tells the two apart before any money is spent.
How much does Printware iJetColor Pro 1175P printhead repair cost?
It is quoted per case, because the cost depends on the failure mode and on whether the ink delivery system also needs service. Send the nozzle test and you get a scope and a price up front.
Other machines we service
HP
HP FI-1000 printhead repair
The 297 mm HP Fixed Imager 1000 printhead itself — the part that fails in every FI-1000 based machine, whatever badge is on the front.
Boxmaking Machinery GmbH
Boxmaking Machinery BM300 printhead repair
Single-pass packaging press built directly around the HP FI-1000, printing bags, boxes, mailers and envelopes at up to 27 m/min.
Printware / iJetColor
Printware iJetColor Pro PXG printhead repair
Packaging-oriented member of the iJetColor Pro series using the HP FI-1000 fixed imager, launched at PackExpo 2021.
All machines: printhead repair overview.
Get a diagnosis for your iJetColor Pro 1175P
Send a nozzle test print and a short note on what the machine was doing when the fault appeared.